1987 Chevy K10 Lifted Mud Truck for Sale.
This Mud Truck has been Sold or removed by Owner.
I have done so much to this mud truck it will be impossible to list all that was done/rebuilt. Please send me any questions you have or offers. Will entertain reasonable offers. 1987 Chevy K10 5.7L V8, TBI fuel injected, 700r4 transmission, NP208 transfer case. 6" lift, Front and Rear lockers. This was a half ton V10 (chevy changed the K10 name to V10 in 1987 only to distinguish from the 1988 trucks, it is identical to other 83-87 Chevy K10s, except it is factory TBI fuel injected). Custom front winch mount plate is included but the Winch is not included in sale. I do have the factory bumper but it is not currently on.
Upgraded to 3/4 status, (full float corporate 14 bolt), 8 lug K20 front hubs.Full Float 14 bolt rear end: Fully rebuilt seals, ALL bearings (timken), Detroit Locker ($500), Rear DISK brake Conversion (uses chevy 1/2 ton front calipers/rotors). Brand new rotors, brand new calipers, brand new pads. Off road designs (ORD) rear stainless braided brake lines, ORD stainless rear brake line drop line. New 4.56 Richmond Gearset and bearings.
Front 8 lug K20 conversion: Brand new rotors, calipers, pads. Stainless Braided Brake Lines. Spartan front locker ($400), Warn HD lockable hubs. Completely rebuilt bearings, hubs with new Tinken bearings and seals. New 4.56 Richmond Gearset and new bearings.
Engine: Stock 5.7L TBI V8. Brand new injectors, new plug wires, new distributor, new manifolds, 100% new sensors (O2, MAP, coolant temp, etc). TBI unit rebuilt (new injectors, fuel pressure regulator rebuild kit, new gaskets), new valve cover gaskets. Brand new Champion all aluminium heady duty racing radiator.
New gas tank, NEW fuel pump, new filter.Trans/Transfer Case: 700r4 has a shift kit and shifts really solid into 2nd. All 4 gears no slipping. Transfer case was JUST rebuilt/resealed with one out of a 40k mile truck, totally rebuilt all bearings and chain anyway just in case. New U-joints on front axles, front driveshaft, rear driveshaft. Heavy duty 1350 rear pinion yoke.
Interior: MP3/Bluetooth Radio, new 5x7 rear speakers added in custom boxes in cab corner. Backup camera, accessory switches, LED dash lights, interior lights.
Body/Frame: 6" Skyjacker softride springs all the way around (not cheap blocks). Rear springs have less than 500 miles on them. Off Road Designs (ORD) steering box brace kit. ORD swaybar disconnect kit. ORD Heavy Duty tie rod.
Wheels tires: Trail Worth Fab re-centered Humvee 24 bolt double beadlock and runflat rims with Goodyear Military Wrangler 37" tires with ~85%+tread left). These are the newer 37's not the older 36's. These RIMs cost $951 alone.
The bad: Body has several moderate dents on the right side of the bed. Front fenders need to be trimmed (37's clear 100% fine lock to lock in normal driving but will rub slightly if off road). COMES WITH SET OF NEW PERFECT FRONT FENDERS. Motor has no doubt been rebuilt once and probably could use another. Compression is good but sounding a little tired these days. My goal was to LS swap this and then I would drive it forever but I do not have the time to do it right now.
Mud Truck is by NO means perfect. Right side of the body has several dents. Most of the the frame has been painted black, paint on body is a crappy black paint job thats coming off in multiple areas. Truck was originally blue. This is NOT a show truck so please dont expect that. But it is running and driving and would probably take you to Canada and back right now along with over a mountain and through the snow and mud no problem. I have spent well over $7,000 in parts and rebuild parts, all this thing really needs is an LS swap and a paint/body job and it would be amazing, sadly I just dont have the time right now to finish this up. Below is just a partial list of what I have done. Please email me any questions and reasonable offers. Asking 6500.
- Energy Suspension 9.13119G Round Style Tie-Rod End Boot - Pack of 2
- ACDelco 213-1545 GM Original Equipment Manifold Absolute Pressure Sensor
- ACDelco EGS20 Professional Engine Ground Strap
- EGR Valve ACDelco 214-5074
- Monroe SC2913 Magnum Steering Damper
- Monroe SA1997 Shock-Mate Shock Absorber Boot Kit
- 2 of ACDelco 217-2286 Professional Throttle Body Fuel Injector Assembly
- ACDelco GF652 Professional Fuel Filter
- ACDelco 9618V Professional Spark Plug Wire Set
- 2 of ACDelco 291-324 GM Original Equipment Rear Axle Shaft Seal
- OLS PSZACCEPS151S 12V DC 15 Amp 3 Port Cigarette Lighter Adapter Outlet Extension Box With On/Off Switch
- OLS PSZACCEPS051H 6-Way LED Illuminated Blade Fuse Box with Cover
- 2 of Timken 6408 Cylindrical Wheel Bearing
- Fel-Pro RDS550281 Rear Axle Housing Gasket
- METRA Ltd 70-1677-1 78 - 91 Gm Vehicle Harness
- La Speedometer Gear 1359273 39 Tooth Speedometer Driven Gear
- ACDelco 252-595 Professional Water Pump
- Metra GM Chevy Truck 1973-1987 2-SHAFT Or DIN Pocket Trim Plate - Metra 87993052
- METRA Ltd 70-1677-1 78 - 91 Gm Vehicle Harness
- ACDelco 213-80 GM Original Equipment Engine Coolant Temperature Sensor
- ACDelco 19244932 GM Original Equipment Engine Oil Pressure Sensor
- Blue Sea Systems ST Blade Fuse Block - 12 Circuits with Negative Bus & Cover
- Feniex Industries C-1060 Haleo 600 6 Red Lighted Switch Panel
- Skyjacker CR16S 6" Softride Leaf Spring
March 2016
Used 14 Bolt Full Float axle from 85-87 Chevy K20 Suburban -Completely rebuild, all new bearings seals and races, including hubs.
- Barnes 4wd Shave Cover
- Barnes allen head cover bolts
- Motive Gear R14RMKLT Master Bearing Kit
- Yukon (SK CSGM14T) Crush Sleeve Eliminator Kit for GM 14-Bolt Truck 10.5" Differential
- Timken SET38 Bearing Set
- 2 of Timken 387AS Bearing
- Timken 2081 Seal
- 2 of Timken 382A Wheel Bearing
- Detroit Locker 225S10 Differential Locker with 30 Spline for GM 10.5", 14 Bolt Rear End
- Set of 4 2" Inch (50mm) 8x6.5 to 8 X 6.5 Wheel Spacers Adapters 9/16" Studs
- USA Standard Gear (ZG GM14T-456T) Ring and Pinion Gear Set for GM 14-Bolt Truck 10.5" Differential
- Raybestos 56287R Professional Grade Disc Brake Rotor & Hub Assembly
- ACDelco 18A61A Advantage Non-Coated Front Disc Brake Rotor (14 bolt conversion)
- Barnes disc brake conversion brakets
- Off Road Design Full Length DOT cert. Stainless steel rear brake hose for 14bff swap
February 2016
- Moog ES362S Steering Center Link Tie Rod End
- Moog ES2027L Steering Center Link Tie Rod End
- Moog ES2026R Steering Center Link Tie Rod End
- Dorman HELP! 82590 Coolant Cap
- Dorman 901-017 Power Window Switch
- ACDelco 213-80 GM Original Equipment Engine Coolant Temperature Sensor
January 2016
- ACDelco D1588 GM Original Equipment Headlamp Switch - fixed flickering
- Energy Suspension 3.2111R Front Spring Bush for GM 4WD
- Energy Suspension Part Number: 9.9429
- Product Name: Front Leaf Spring Bushings - 1 1/8 inch ID for SuperLift and Skyjacker Springs
- OFFROAD DESIGN heavy duty tie rod $85
- Moog ES2010R Steering Center Link Tie Rod End
- Moog ES2010L Steering Center Link Tie Rod End
- ACDelco 12F46 Professional Fuel Tank Cap
- Replaced cargo light with 1142 LED bulb
- GRV Ba15d 1142 1076 High Bright Car LED Bulb 18-5050SMD DC12V Cool White Pack of 2
- REplaced dome light with LED:
- Cutequeen Trading White 42mm(1.72") 16-smd 12v Festoon Dome Light LED Bulbs 211-2 212-2 569 578 - White (Pack of 4)
- Drilled and tapped front axle for brass threaded insert and new breather hose run into engine bay.
Front Driveshaft shortened and balanced by Driveshaft Services Marietta GA, $60-$80? I think 80. New Neapco front U-joint conversion from S44 (driveshaft) to 1310
November 2015
- Rebuilt front differential with new 4.56 gears, installed spartan locker. All new seals, new U-joints, axles painted black.
- Removed intake manifold and put in new manifold gaskets.
- Fel-Pro MS93317 Manifold Gasket Set
- Mr. Gasket 2661 Chrome O-Ring Water Neck
- ACDelco 18M217 Professional Durastop Brake Master Cylinder Assembly
- USA Standard Gear (ZK GM8.5-F) Master Overhaul Kit for GM 8.5" Front Differential
- 2 of ACDelco 18A35A Advantage Front Disc Brake Rotor
- Oreily Auto New Rebuilt Calipers
- Oreily New brake pads ceramic
- New Caliper Slide Pins
- 2 of Spicer 5-760X U-Joint Kit
- Stant 45358 SuperStat Thermostat - 180 Degrees Fahrenheit
- Spartan locker for GM 8.5" with 28 spline axles, includes heavy-duty cross pin shaft.
- USA Standard Gear (ZK GM8.5-F) Master Overhaul Kit for GM 8.5" Front Differential
- JEGS Performance Products 61252 Basic Differential Installation Kit
- 2 of USA Standard Gear (ZG GM8.5-456) Ring and Pinion Gear Set for GM 8.5" Differential
- 2 of Timken 6408 Cylindrical Wheel Bearing
- Timken SET45 Bearing Set
- Yukon (SK CSGM8.5) Crush Sleeve Eliminator Kit for GM 8.5"/Chrysler 9.25" Differential
- 2 New Skyjacker H7071 Softride Hydro Shock Absorber - previouis were too short
- 2 of Dana Spicer 28068X Dana Spindle Nut Kit
- ACDelco 12458080 GM Original Equipment Rear Axle Housing Magnet
- ACDelco 29535617 GM Original Equipment Automatic Transmission Fluid Pan Magnet
- 2 of Mr. Gasket 9728 Competition Wire Separator Kit - Black
- Stant 10330 Lev-R-Vent Radiator Cap - 16 PSI
- Spicer 2-70-48X Bearing Strap Kit
- Yukon (YSPPN-018) Pinion Nut
September 2015
- 2 of USA Standard Gear (ZG GM8.5-456) Ring and Pinion Gear Set for GM 8.5" Differential
- Yukon (SK CSGM8.5) Crush Sleeve Eliminator Kit for GM 8.5"/Chrysler 9.25" Differential
- Timken M802048 Pinion Bearing (inner)
- Timken M802011 Wheel Bearing (inner)
- Timken M88010 Wheel Bearing (outer)
- Timken M88010 Wheel Bearing (outer)
- JEGS Performance Products 61252 Basic Differential Installation Kit
Setup Notes:
Final pinion preload 15 in lbs before seal, after seal and torqued to 125 ft lbs with med thread locker was between 15-20. Final backlash is 0.006" exactly what it was with the setup bearings Cleaned all bearings, main caps to 65ft lbs dry torque.
August 2015
- ACDelco 213-3859 Professional Throttle Position Sensor
- 2 of ACDelco 217-2286 Professional Throttle Body Fuel Injector Assembly
- Changing injectors did not change misfire, now has slight hunting at idle.
- Cleaned and relubed front left caliper slide pins.
- Bled rear brakes.
- Replaced IAC valve with standard motor products. Performed minimum air adjustment and tips setting.
- Old c9 crank wire was unable to be located and a new wire was run from the 3amp crank fuse on the fuse block.
- New right rear taillight housing installed glo bright
June 2015
- ACDelco EGS20 Professional Engine Ground Strap - Mech. pump cover to frame rails
- Cleaned grounds at alternator and frame rails. Ground at manifold stud is not working, but is grounded internally at the ECM.
- ACDelco D1405B GM Original Equipment Ignition Switch
- ACDelco CV774C GM Original Equipment Positive Crank Ventilation (PCV) Valve
- Standard Motor Products AC1 Idle Air Control Valve
- Dorman 03401 Exhaust Flange Hardware Kit
- Chevy Pick-up Dash Cover Mat Pad - Fits 1981 - 1987 (Custom Carpet, Black)
- Dorman 674-231 Exhaust Manifold Kit
- Dorman 674-158 Exhaust Manifold Kit
Old fuel system removed. Old switching valve was leaking gas out of the electrical ports, removed both old tanks, replaced with new tank, sending unit, pump, strainer. New filter put on few months ago was still clear. New hose clamps on all hoses, new Gates brand rubber fuel lines from tank to hard lines. Ran new vent line into a spiral and through a gas filter, exiting near fill door. Old pump was very loud, new pump is almost silent.
- Spectra Premium GM11C Fuel Tank for General Motors
- Spectra Premium FG05N Sending Unit for General Motors
- Delphi FE0115 Electric Fuel Pump Motor
- Delphi FS0177 Fuel Strainer
- ACDelco 337-1022 Professional Starter - with Chevrolet Performance Starter Motor Bolts 12338064
After new fuel system and starter, truck went from taking 4-5 seconds to start to starting between 1 and 2 seconds. Truck used to not try and start, now it starts to try and start immediately.
April 2015:
- Backing plates cleaned, grooves ground out+polished, painted black, and lubed with Permatex Silver anti-seize
- Brake Best Drum Hardware Kit - Part # H2324 Line: BHH
- Brake Best Select brake shoes Part # 473 Line: BB
- Brake Best Wheel Cylinders - Part # WC51081 Line: BHH
- Cut off old rear brake line drop and re-double flared with new nut to install extended drop.
- Skyjacker (RBL20) 6"- 8" Stainless Steel Brake Line
- Bled all brake lines
- Brake Best parking brake cables (rear,left and right) Part # BC93248 Line: BHH / Part # BC93249 Line: BHH
- Old Knock Sensor abandoned - could not remove. New ACDelco 213-324 Knock sensor installed on driver side fitting
- 2x new Dorman parking brake struts Part # 21149 Line: MTM
- Painted grill and headlight covers Duplicolor Trim and bumper paint.
- Replaced right rear tailight housing Glo-Brite
- Spark Plug Protect Boot Heat Shield Thermal Protection Insulator 8 Cyl
- ACDelco CR43 spark plugs gapped 0.040" (i think, may have been 045 but all were gapped equally)
- Hayden Automotive 678 Rapid-Cool Plate and Fin Transmission Cooler
March 2015:
- Replace Fuel Pump Relay (spare left in place)ACDelco 15-8240 GM Original Equipment Multi-Purpose Relay
- Richporter Technology by Spectra Premium GM04 Distributor $81.44 Set at 0° Advance
- (with new AC Delco Ignition module) : ACDelco D1943A GM Original Equipment Ignition Control Module $49.36
- New ATP Y-613 Accelerator Cable $19.22
- Adjusted Rocker Arms per Spec (1/2 turn extra)
- New Fel-Pro valve cover gaskets
- Goodyear 4050435 Gatorback Poly-V Belts
- Gates 7395 V-Belt
January 2015:
- Rebuilt TBI: ACDelco 219-607 Professional Fuel Injection Throttle Body Repair Kit
- Increased Fuel Pressure 1 full turn-stock regulator made adjustable –Tested at 13.0 psi steady
- Cap and Rotor: MSD Ignition 8406 Distributor Cap and Rotor Kit
- FR FL marker lenses: TYC 18-1201-01, TYC 18-1200-01
- ACDelco D503A Professional Ignition Coil
- Denso 234-1001 Oxygen Sensor
- 02 Sensor Pigtail/Connector Dorman -Oreilys
- JEGS Performance Products 40213 8.0mm Red Hot Pow'r Wires
- ACDelco 214-329 GM Original Equipment EGR Vacuum Solenoid
- Knock Sensor Connector/Pigtail: BWD PT770
- LT1 TBI EGR VALVE DELETE PLATE BLOCK OFF Chevy Throttle Body 614
- ACDelco GF652 Professional Fuel Filter
- Delphi TS10075 Engine Coolant Temperature Sensor
December 2014:
- Skyjacker Hydro 7000 rear shocks w/ bushings, upper shock mounts bolts.
- L&R Energy Suspension Motor Mounts (red and black)Energy Suspension 3.1116G Clam Shell Type Engine Mount for GM, Energy Suspension 3.1116R Clam Shell Type Engine Mount for GM
- Transmission mount (Westar EM2638 Engine Mount)
- LED gauge lights T10 168 blue LEDs
- Cleaned out Axel tubes
- Cleaned and two part epoxy magnet inside diff case
For more information about this Mud Truck for Sale.